 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SU1086 1.5A Low Dropout Positive Elektronische Bauelemente RoHS Compliant Product Adjustable or Fixed-Mode Regulator Description The SU1086 is a low dropout at positive adjustable or fixed-mode regulator with min. of 1.5 A output current capability. The product is specifically designed to provide well-regulated supply for low voltage IC applications such as high-speed bus termination and low current 3.3V logic supply. SU1086 is also well suited for other applications such as VGA cards. SU1086 is guaranteed to have lower than 1.4V dropout at full load current making it ideal to provide well regulated outputs of 1.25 to 5V with 4.7 to 12V input supply. Features * 1.4V Max. Dropout Full Load Current * 3-Terminal Adjustable or Fixed 1.5V,1.8V,2.5V,3.3V,5.0V * Output Current Limiting * Fast Transient Response * Built-in Thermal Shutdown REF. A b L4 c L3 L1 E Millimeter REF. Min. Max. 4.40 4.80 c2 0.76 1.00 b2 0.00 0.30 B D 0.36 0.5 e 1.50 REF. L 2.29 2.79 9.80 10.4 L2 Millimeter Min. Max. 1.25 1.45 1.17 1.47 8.6 9.0 2.54 REF. 14.6 15.8 0 8 1.27 REF. Typical Circuit Block Diagram http://www.SeCoSGmbH.com/ Any changing of specification will not be informed individual 01-Jun-2002 Rev. A Page 1 of 4 SU1086 Elektronische Bauelemente 1.5A Low Dropout Positive Adjustable or Fixed-Mode Regulator Pin Descriptions Name Adj (GND) Vout O I/O PIN# 1 2 Adjustable (Ground only for fixed mode) The output of the regulator. A minimum of 10uF capacitor must be connected from this pin to ground to insure stability. The input pin of regulator .Typically a large storage capacitor is connected from this pin to ground to insure that the input voltage does not sag below the min. dropout voltage during the load transient response .This pin must always be 1.4V higher than Vout in order for the device to regulate properly. tage does not sag below the minimum dropout voltage during the load V higher than Vout in order for the device to FUNCTION Vin I 3 Absolute Maximum Ratings Parameter DC Supply Voltage Power Dissipation Storage Temperature Range Operating Juction Temperature Range Symbol VIN PD TST TOP Ratings -0.3 to 12 Internally Limited -65~+150 0~+150 Unit V o o C C Electrical Characteristics Parameter Reference Voltage SU1086-ADJ SU1086-1.5 SU1086-1.8 Output Voltage SU1086-2.5 SU1086-3.3 SU1086-5.0 Line Regulator SU1086-XXX SU1086-ADJ SU1086-1.5 Load Regulation SU1086-1.8 SU1086-2.5 SU1086-3.3 SU1086-5.0 Dropout Voltage (Vin-Vout) Current Limit Minimum Load Current Thermal Regulation Ripple Rejection Temperature Stability Thermal Resistance Junction-to-Ambient Thermal Resistance Junction-to-Case SU1086-XXX SU1086-XXX SU1086-XXX TA=25 , 30ms pulse F=120Hz, COUT=25uF, Tantalum, Io=1.5A SU1086-XXX Io=10mA Vin=Vout+3V Control Circuitry/Power Transistor 60 0.5 83 0.65/2.7 70 dB % /W Conditions Io=10mA, TJ =25 , (Vin-Vout )=1.5V Io=10mA, TJ =25 , 3V Vin 12V Io=10mA, TJ =25 , 3.3V Vin 12V Io=10mA, TJ =25 , 4V Vin 12V Io=10mA, TJ =25 , 4.8V Vin 12V Io=10mA, TJ =25 , 6.5V Vin 12V Io=10mA, Vout+1.5 TYP 1.250 1.500 1.800 2.500 3.300 5.000 12 15 20 26 40 1.3 5 0.008 MAX 1.275 1.530 1.836 2.550 3.365 5.100 0.2 1 15 18 25 33 50 1.4 10 0.04 UNIT V V V V V V % % mV mV mV mV mV V A mA %/W (No heat sink ;No air flow) /W Note 1: See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction Temperature by low duty cycle pulse testing. Load regulation is measured at the output lead =1/18" from the package. Note 2: Line and load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the difference in input and output and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range. Note 3: Quiescent current is defined as the minimum output current required in maintaining regulation. At 12V input/output differential the device is guaranteed to regulate if the output current is greater than 10mA. http://www.SeCoSGmbH.com/ Any changing of specification will not be informed individual 01-Jun-2002 Rev. A Page 2 of 4 SU1086 Elektronische Bauelemente 1.5A Low Dropout Positive Adjustable or Fixed-Mode Regulator Functional Description Introduction The SU1086 adjustable or fixed-mode Low Dropout (LDO) regulator is a 3 terminal device which can easily be programmed by internal mask change to any voltage within the range of 1.25 to Vin-1.4V. The SU1086 only needs 1.4V differential between Vin and Vout to maintain output regulation, in addition, the output voltage tolerances are also extremely tight and they include the transient response as port of the specification. For example, Intel VRE specification calls for a total of +/-100mV including initial tolerance, load regulation and 0 to 1.5A load step. The SU1086 is specifically designed to meet the fast current transient needs as well as providing an accurate initial voltage, reducing the overall system cost with the need for fewer output capacitors. Load Regulation Since the SU1086 is only a 3 terminal device, it is not possible to provide true remote sensing of the output voltage at the load. But it can supply good load regulation by internal feedback bypass the external loss such as adjustable mode. Stability The SU1086 requires the use of an output capacitor as part of the frequency compensation in order to make the regulator stable .For most applications a minimum of 10uF aluminum electrolytic capacitor insures both stability and good transient response. Thermal Design The SU1086 incorporates an internal shutdown that protects the device when the junction temperature exceeds the maximum allowable junction temperatures. Although this device can operate with junction temperatures in the range of 150 : , it is recommended that the selected heat sink be chosen such that during maximum continuous load operation the junction temperature is kept below the temperature. Layout Consideration The output capacitors must be located as close to the Vout terminal of the device as possible .It is recommended to use a section of a layer of the PC board as a plane to connect the Vout pin to the output capacitors to prevent any high frequency oscillation that may result due to excessive trace inductance. h tp://www.SeCoSGmbH.com/ Any changing of specification will not be informed individual 01-Jun-2002 Rev. A Page 3 of 4 SU1086 Elektronische Bauelemente 1.5A Low Dropout Positive Adjustable or Fixed-Mode Regulator Performance Characteristics h tp://www.SeCoSGmbH.com/ Any changing of specification will not be informed individual 01-Jun-2002 Rev. A Page 4 of 4 |
Price & Availability of SU1086
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |